Acropolis Rally
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroLHF.jpg)
By Phil Wicks
Team Slot are still a long way down the road when it comes to slotcar making but compared to what we could buy ten or so years ago they are catching up. I don’t know if they will ever equal the like of Scalextric and co for all round finish and drivability but if my latest acquisition is indicative of a trend then they will be a lot closer to the market leaders in a couple of years!
My first Team Slot experience was the ill fated Toyota Celica GT4 (see review, this board) It wasn’t a disappointment as I had no expectations of it but it certainly let itself down badly. My next Team Slot experience was the Renault Alpine Rally car in factory colours. This model took a bit of working on but eventually at minimal cost I turned it into a race winner. The TS 6 motor was far more tractable for small track / home circuit use.
A few weeks back whilst perusing the pages of John Hayward’s ‘Classic slot’ web site I saw the Audi Quattro ‘Acropolis Rally’ model. My previous experience with Quattros was the Scalextric model. Very attractive but very, very hard to drive. Like a lot of the earlier Scalextric saloon/sedan car models, there is a lot of weight above the axles and the end result is a model which does spectacular roll over deslots!!
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroRHside.jpg)
So, apart from a little trepidation, not knowing what motor it would have and how good the body and chassis mouldings would be and whilst waiting for some of the more desirable announcements from other manufacturers to materialise, I decided to purchase this model with a view to getting it ‘working’.
As an overseas buyer, EU rules allow me to purchase this model free of VAT (GST) and at 17.5% this makes the model very attractive. Aussie customs and excise rules allow non commercial transactions below $200 exempt from duty, so this too was very attractive!! And finally, after a Paypal transaction of Au$55.00, the model was on its way. Five days later, I was eagerly unwrapping it in the comfort of my lounge.
Out of the box my first instinct was to whip it over and view the motor, as expected, it was the TS7 Titan!! A mean beast with plenty of sting. Not really a home track / small track motor but in a good chassis it can be partially tamed. Further inspection of the exterior showed the finish to be greatly improved on the GT4. No tampo fading out towards the edges and no over spraying of other parts. The axles, too, felt fairly firm in their bushes and the body detail is a vast improvement on my previous experiences with Team slot.
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroRear.jpg)
One thing that caught my attention was the rear end detail. No doubt the soon to be released Fly version will have a well moulded rear end but, for Teamslot, this is a milestone in detail reproduction!! Another plus was that the model actually sits level on its chassis and is square to the track. The other Teamslots I’ve owned have had their mounting posts trimmed to get things level! Almost worth the purchase alone! Looking closer, some of the not so hot features become apparent but hey, this is to race!!
The model has quite a heavy clear coat on it, maybe one too many, and wherever the model is sprayed, I think they should improve the dust extraction equipment. There are specs of dust or fall out in several noticeable places on the upper body. Another area for review must be the moulding itself. It looks scale enough and in good proportion but like some of the static plastic models of the sixties and seventies, there are ‘dimples’ in the moulding at the extremities, front and rear. Minor, but still there.
The driver and navigator are pretty nineties and interior detail for this in line model is rudimentary but it does well in conveying the visual effect of the . The colour scheme too is a fair likeness and with red and black parts being very bold, it stands out in a crowd on the track! Lastly, the vulnerable parts consist of both door mirrors, as they stick out into the roll over zone, and the rear spoiler comes across as a bit flimsy but it does have a simulated oil cooler mounted in it so this may well brace it a bit!
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroLHR.jpg)
Next job was to poke about inside a bit. Three tight screws fix the body. Two up front and one rear. The mounting posts don’t interlock with the chassis as do a lot of modern models so it is up to the chassis to sit between the body sides to hold all in place. This will make body tuning a breeze.
The model is four wheel drive, this is a bit tongue in cheek as the front wheels are driven by a familiar rubber band on one side only. The belt tension is quite low and its effectiveness will have to be tested. I usually test this sort of set up by turning the front wheels. A good set up will turn the rear axle too but this system slips easily and power transmission from rear to front looks like it’s going to be rudimentary! Also, on later inspection, it was noted that the front pulley was actually split on the shaft!! The sloppy belt is probably a blessing in disguise as any more tension on the pulley may well be problematic.
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroChassistop.jpg)
Next check was the guide. This is similar to other team slot ‘spring loaded’ guides. Not too much tension here either and it is a poor attempt at a spring loaded guide. The saving grace is that the guide is quite rigid in its mounting and front/back and side to side slop is minimal.
Next, to the motor. This sits in an adapter. The TS7 Titan is externally the same as the Ninco NC 5 motors in appearance and the hole in the chassis is quite large? The end result is a motor that has virtually no resistance to torque reaction what so ever! The motor will eventually have a thick bead of hot glue down both sides to stop this twisting.
The front and rear axles are fairly well mounted and axle/bush slop is minimal although the axle bushes do rotate readily in the chassis. My solution here was to fix the rear axle bushes with some PVA glue. This will do the job well and will be easy to release when it is necessary. The chassis is a loose fit in the body so there are no pinch points which might need treatment.
Tyres are not the best. They are eccentric and have poor grip. My previous experience with Teamslot tyres has been to discard the rears and replace them with SCX type seven slicks. These seem to have plenty of grip for both board and plastic tracks. The wheels on the other hand are fine (this time) and don’t have any noticeable eccentricity or run out. A saving grace on a model that is going to take some setting up.
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroChassisunder.jpg)
The model’s first outing was at a friends classic Scaley layout but this was more a try it and see event. It wasn’t possible to run the car flat out as the undulations in the plastic track caused the model to become airborne after reaching Mach 2! The traction magnet did however demonstrate more that a token amount of downforce. Not of SCX or Scaley proportions but still enough to allow the car to hang on fairly tenaciously in even the tight radius bends! Another observation was the noise emitted from the gears, very reminiscent of SCX models!
So later, after screwing gluing and lubing, next stop had to be the 21 metre painted board test track. At home with the Red Team saw the model wheeled out for its debut. Track warmed up and ready to go, the model was placed in red lane and given its head. The track had already been ‘warmed up’ and a few moderate laps gave me an idea of what to expect under pressure. Pressing on, I decided to run the model on full power.
The track has the facility to ‘dial in’ some wire wound resistors and therefore either tame or handicap a model. On full juice I set off and it was immediately clear that the SCX tyres were working well. With the gear still a bit noisy I pressed on but it did quieten over a period having not been lubed to start with. After twenty laps or so I decided to up the pace. Make no mistake, the TS7 ‘Titan’ motor has plenty of grunt. In my Celica GT4 test it made the car almost undrivable, due in part to the poor chassis. This model retained a semblance of controllability but the car is still blisteringly quick. Too quick for the average home circuit. It would be more useable on a big club circuit and then it will be a handful, the main reason being the cars high centre of gravity.
![Image](http://www.slotcarouthouse.com/photos/TeamslotAudiQuattroBodyunder.jpg)
I punched out a few unnerving laps and finally, the tyres bedded in well and the extra grip caused a tipping deslot in the sweepers. C of G was going to need attention still though. The ‘yump’ on the back straight caused the model to become airborne but in this cars case, nine out of ten times it landed back in the slot??!! allowing me to continue on my breakneck way! Finally, I reset the race manager and pushed of for the hottest lap. Hold on to your seats!
The model flies, it is possible to control it but every corner is a potential off and you can’t run that high speed ‘relaxed’ type of race. It’s ragged ‘edge’ every time! This model should be raced with lane stickers top AND bottom! After a period of high speed passes, best time was 7.643 secs, My next step was to clean the tyres and set off again. With a light smear of CRC (WD40) on the rear rears, the grip level seems to increase dramatically but as mentioned before, the high centre of gravity may well work against having too much grip and corners had to be notched back a bit. Nonetheless, the model is a very quick car and after final testing, the best lap came in at 7.216 secs. No slouch at that but still no time to relax!
Statistics Wheelbase 79.0 m.m. Front Axle width 59.5 m.m. Rear Axle width (SCX tyres) 62.0 m.m. Turret height 41.5 m.m. Height / width ratio 0.67 : 1 Overall weight 94.0 gms Front Axle load 36.0 gms Rear Axle load 58.0 gms Front / Rear weight dist. 39% / 61% Pinion 9z Crown wheel 27z Final drive ratio 3 : 1 Rear wheel diameter 19.0 m.m.